Michigan Wheat: Planting the 2022 Crop

    Wheat planter. Photo: Martin Nagelkirk, Michigan State University

    Planting preparations

    Achieving top yields requires a uniform stand of healthy seedlings. This is dependent on seeds being dropped as evenly as possible and at a uniform depth. Good seed placement, in turn, requires that fields are appropriately prepped, and planting equipment receive disciplined inspection, necessary adjustments and deliberate calibrations.

    Tillage systems

    Wheat establishment can be successful under conventional, minimum tillage and no-till systems. Generally speaking, no-till has won favor in recent years. It tends to result in more unevenness in the stand, but it can often provide improved moisture retention and less susceptibility to cold temperature damage.

    Tillage, even at a minimal level, can be helpful in distributing and incorporating residue, fertilizer and lime; and create a more uniform seedbed. Tillage can also be useful when attempting to reduce disease inoculum borne in crop residue (e.g. corn stubble or stalks infected with Fusarium).

    Seeding date

    Ideally, winter wheat is planted while the soil and air temperatures are still warm to ensure that seedlings can emerge quickly and in plenty of time to develop a couple of tillers and a strong root system. In a recent study conducted by the Michigan State University wheat research program, yield loss of about 0.6 bushels per day occurs when planting after Oct. 1.

    While the Hessian fly no longer poses a significant threat to wheat in Michigan, the fly-free-date is still a useful reference (Table 1). The standard fly-free-date is during the first week of September in the northern Lower Peninsula, around mid-September in mid-state areas and approximately the third or fourth week of September for southern Michigan. Highest yields are often attained when seedlings emerge within two weeks following the posted fly-free-date, assuming heat unit accumulation is near normal in October and November.

    When wheat is planted within a few days of the fly-free-date, seeding rates and fall-applied nitrogen rates should be significantly reduced to avoid excessive growth. The goal is to plant early enough to achieve two to three tillers produced prior to the winter vernalization period.

    Table 1. Hessian fly-free-dates for Michigan
    County Sept. County Sept. County Sept. County Sept.
    Alcona 6 Eaton 16 Lapeer 15 Ogemaw 10
    Allegan 20 Emmett 4 Leelanau 8 Osceola 10
    Alpena 9 Genesee 17 Lenawee 25 Oscoda 7
    Antrim 4 Gladwin 12 Livingston 16 Otsego 6
    Arenac 13 Grand Traverse 8 Macomb 18 Ottawa 19
    Barry 18 Gratiot 15 Manistee 13 Presque Isle 8
    Bay 14 Hillsdale 19 Mason 13 Roscommon 7
    Benzie 16 Huron 13 Mecosta 12 Saginaw 16
    Berrien 23 Ingham 17 Midland 15 Sanilac 15
    Branch 19 Ionia 16 Missaukee 9 St. Clair 16
    Calhoun 19 Iosco 7 Monroe 21 St. Joseph 23
    Cass 22 Isabella 11 Montcalm 15 Shiawassee 16
    Charlevoix 3 Jackson 16 Montmorency 7 Tuscola 15
    Cheboygan 4 Kalamazoo 20 Muskegon 18 Van Buren 22
    Clare 12 Kalkaska 5 Newaygo 15 Washtenaw 18
    Clinton 17 Kent 18 Oakland 16 Wayne 18
    Crawford 6 Lake 13 Oceana 16 Wexford 9

    Oftentimes, weather conditions make it difficult to plant wheat on time. How late a wheat crop can be planted is really a question of how much risk a grower is willing to take. If a grower expects to have the crop insured, then the answer is straightforward because Oct. 25 is the last planting date for crop insurance eligibility.

    AgFax Weed Solutions

    For those trying to estimate the odds of achieving a reasonable yield, it is important to recognize that the challenge to late wheat is not only the inherent constraints on grain yield, but also its greater susceptibility to winter injury.

    Planting wheat on time starts with the previous crop. Soybean fields that are to be planted to wheat in the fall can benefit from management considerations such as optimum planting time and maturity group (MG) selection (Figure 1). Selection of late-maturity soybean varieties (e.g., 3.0 versus 2.0 MG) before May 15 planting can lead to 5-8 bushels per acre increase in soybean yield, while still reaching maturity by late-September.

    This system would provide greater soybean yields while allowing adequate time for an optimum wheat planting date after soybean harvest. However, for later soybean plantings (after mid-May), early-maturity varieties can be used without a soybean yield penalty while allowing adequate time for wheat planting.

    Impact of planting date and maturity group selection

    Figure 1. Impact of planting date and maturity group selection on soybean seed yield (bu/acre, left panel) and date to reach R7 stage (one mature pod on the main stem, right panel). Add 15-20 days to R7 to estimate harvest date. Data is average of four Michigan site-years. Click Image to Enlarge

    Seeding depth

    Attaining a consistent seed depth is important in order to increase the probability of even emergence. Usually, a planting depth of 1 to 1.5 inches is enough in heavy soil. Deeper seed placement may have an advantage when some types of winter stresses occur, but usually this is outweighed by the advantage in more rapid emergence posed by more shallowly placed seed. The exception may be where a coarse soil is very dry. In this case, seed should be planted as deep as possible to reach moist soil.

    Seeding rate

    The recommendation is to plant between 1.2 and 2.2 million seeds per acre. Seeding rates on the lower end of the range should be used when planting within a week of the fly-free-date to avoid overly thick stands that can promote disease development and increase the likelihood of lodging the following season. As the calendar advances, seeding rates should become progressively higher. If planting continues into the second half of October, the seeding rate should be increased to at least 1.8 million seeds per acre.

    Table 2 identifies the pounds of seed needed based on the number of seeds per pound and your population target. For example, if seed size is 12,000 seeds per pound and the target seeding rate is 1.4 million seeds per acre, then 117 pounds of seed would be needed per acre.

    Table 3 is useful for assessing the number of seeds being dropped by each row unit (7.5-inch row spacing) and for evaluating actual seedling density. So, with the 1.4 million target, a 7.5-inch drill would drop approximately 20 seeds per foot and, assuming a 92% emergence rate, lead to an estimated 18.5 wheat seedlings.

    Table 2. Relating seed size and target seeding rates to the number of pounds required per acre
    Seed size (seeds per pound) Target seeding rates (millions of seeds per acre)
    1.2 1.4 1.6 1.8 2.0 2.2
    Actual pounds of seed required per acre *
    9,000 133 156 178 200 222 244
    10,000 120 140 160 180 200 220
    11,000 109 127 145 164 182 200
    12000 100 117 133 150 167 183
    13,000 92 108 123 138 154 169
    14,000 86 100 114 129 143 157
    15,000 80 93 107 120 133 147
    16,000 75 88 100 113 125 138
    *Target seeding rate divided by seeds per pound = required pounds of seed per acre.
    Table 3. Relating target seeding rate per acre to seed and seedling numbers (for 7.5-inch row spacing)
    Seeding rate (millions/ac) Seeds per foot of row Seedlings* per foot of row
    1.2 17.2 16.2 (94%)
    1.4 20.1 18.5 (92%)
    1.6 23.0 20.7 (90%)
    1.8 25.8 22.7 (88%)
    2.0 28.7 24.7 (86%)
    2.2 31.6 26.5 (84%)
    *Projected number of seedlings based on an estimated declining emergence rate as percent.

    The Latest

    Send press releases to

    View All Events

    Send press releases to

    View All Events